Now that the wireless LEDs are added via platform leds this patch isn't
required any longer.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Don't setup the default led pin if the ath9k GPIO controller is used
via device tree to prevent collision. In case any of the pins exposed
by the ath9k is used, the phyNtpt trigger needs to be set in userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>

In case that the atheros device tree binding is used, enable access to
the GPIO chip only if the gpio-controller device tree parameter is used
for the ath9k node.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Unset the default LED gpio pin if the same gpio pin is used by a LED
defined via platform LED. This prevents that the default led trigger
gets assigned to this LED and the GPIO value gets changed on
wifi up/down in case the led is not used for signaling the wifi state.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.

Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.

Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.

Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>

Extend the mdadm package to allow to explicitely configure arrays as
well as device list entries.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Update to latest Git in order to import the following fixes:

1d0263b check_data_file_clashes_change: remove duplicated offline root in paths
a00a6a9 buildReplaces: do not add duplicated replacees
9fbedd8 opkg: compare-versions doesn't need any state
45b54f6 opkg_cmd: fix segmentation fault in opkg_compare_versions_cmd()
93de62b opkg_cmd: fix return of opkg compare-versions
51275a8 pkg_src_list_push: remove unused function
947d3d4 pkg_src_list_pop: remove unused function
980cfb2 str_list_push: remove unused function
52c31c1 str_list_prev: remove unused function
7d24212 str_list_last: remove unused function
48142a3 conffile_list_pop: remove unused function
46c5de5 pkg_dest_list_push: remove unused functions
368bb62 nv_pair_list_prev: remove unused function
2985c00 nv_pair_list_last: remove unused function
f5082ac conffile_list_pop: remove unused function
89bf8b9 conffile_list_push: remove unused function
23d31fb active_list_sort: remove unused function
7fe45f2 active_list_add_depend: remove unused function
86b584d pkg_dependence_satisfied: remove unused function
816d330 Fix typo in pkg_hash_fetch_best_installation_candidate.
07f3b02 set_flags_from_control: remove function

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Support for the nct6775/6776 hwmon chips, and other compatibles
in the family as well as the Intel on-chip thermal sensors.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

The HOSTCFLAGS override only works on newer u-boot versions

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes errors during the image builder run

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes: 0b24850e ("busybox: don't install NTP scripts if NTP isn't configured")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Cuts build time on Mac OS X in half by avoiding repeated $(shell) calls
from the build system

Signed-off-by: Felix Fietkau <nbd@nbd.name>

update the qca988x firmware to firmware-5.bin_10.2.4-1.0-00029.
According to LEDE Forum, the new firmware supports mesh mode.
Also, it seems to have several improvements.

Signed-off-by: Changmin Jang <ckdalsdk12@gmail.com>

asm/* includes are not safe for the host build

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes issues with 802.11s

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix fw3 warnings in dhcp script in case fw3 is not enabled

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

Normal packages don't rely on the feed configuration variables for the
build step

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

If you're using Chrony or NTPD you don't want the busybox NTP server
as well.  Make it's installation truly conditional.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [simplify]

Intel(R) 82576 is an adapter which supports SR-IOV. Thus the host can
assign Virtual Functions (VFs) to different VMs by the PCI-E Passthrough
(e.g. VFIO for KVM), to gain different advantages (performance, VF to VF
communications, host kernel offload, etc.).

The driver of the passthroughed VFs is the igbvf (igb is NOT
compatible).

This is essential for VM guests, to enable them to utilize this feature.

Signed-off-by: Ye Tao <tydus@hongo.wide.ad.jp>

3d9f406 rework IPv6 dns address selection (FS#635)
bc6c3ac ndp: keep an exact copy of IPv6 interface addresses
6eb1e01 ndp: code cleanup
eea7d03 rework IPv6 address dump logic
24d21c7 ndp: add syslog debug tracing

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

Some of our local patches have been accepted upstream. And there are
some more relevant changes (mostly for rt2800usb). Import them and
rebase our remaining local patches on top.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.

Signed-off-by: Karl Vogel <karl.vogel@gmail.com>

20c16fc cmake: Make blockd link against libjson-c
92b4c2c libfstools: add basic documentation of mount functions

Signed-off-by: John Crispin <john@phrozen.org>

This is a 3rd party chipset which is not present on all Intel
reference designs, so make it a module rather than baked in (this
will also alleviate conflicts with drivers which also detect some
of the same chipsets).

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

A lot of Ivybridge and Haswell servers have the 82598/82599 Ethernet
controllers.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

These are recommended practices by REC-22 and REC-24 of RFC6092:
"Recommended Simple Security Capabilities in Customer Premises Equipment
(CPE) for Providing Residential IPv6 Internet Service"

Fixes FS#640

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

ath10k tries to fetch board id via otp, but that fails for many chips
like QCA988x, QCA9984 etc. Recent commit cc189c0b removed the earlier
hack that had allowed QCA radios to work, as that hack was incompatible
with the new wifi chips being introduced to the source tree.

Restore functionality for the existing wifi chips by modifying the
return value of the 'board id via otp' function to a value that is recognised
as a harmless error, so that name evaluation continues by using the board file.

Patch originally suggested by Christian Lamparter in forum discussion.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

F2FS depends on the crc32_generic module (NOT crc32c_generic)

Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>

This is needed for F2FS support (it depends on crc32_generic,
not crc32c_generic).

Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>

With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>

- remove unused code within 500-ar9_vr9.patch
- fixed return of IFX_ERROR (solves SIGSEGV in asterisk at failure)
- align it a bit with 400-falcon.patch
- remove 600-kernel-4.9.patch since changed parts
  are removed during cleanup

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>

Make scan output useful for 802.11s meshes. The common print_ssid function
is used, so this doesn't add any additional code.

Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

modify 500-ar9_vr9.patch from
commit 29367aac ("lantiq: ltq-vmmc add support for ar9-vr9")

- remove unused dependencies to external watchdog functions
  (wdog setup is already disabled)
- using header file from kernel (asm/vpe.h) instead patched file (vpe.h)
- cleanup whitspace warning

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>

Do not select the qca988x by default as soon as kmod-ath10k is
selected. We do support more ath10k chips than the qca988x in the
meantime, so this dependency doesn't make sense any longer.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Fixes FS#637

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

0463b05 dhcpv6: rebind capability support in reconfigure message (rfc6644)
53767fc dhcpv6: respect renew end point when handling reconfigure message
dd892e2 dhcpv6: calculate T1, T2 and T3 in a more sane manner
8a6ca6e md5: use libubox md5 library as local implementation
89822de dhcpv6: don't return renew msg in case of invalid msg type in reconfigure msg
4160c0e treewide: align coding style

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lowr limits than the CTLs
of the user configured regdomain.

To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.

Signed-off-by: Felix Fietkau <nbd@nbd.name>