- Dec 21, 2013
-
-
Jo-Philipp Wich authored
- cache udhcp check results to speed up subsequent reloads - enable procd file tracking for /var/etc/dnsmasq.conf to only reload service if needed - implement reload action to only restart dnsmasq if /var/etc/dnsmasq.conf actually changed - launch dnsmasq from interface hotplug to avoid race conditions with network bringup Signed-off-by:Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 39152
-
- Dec 20, 2013
-
-
Imre Kaloz authored
Signed-off-by:Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39151
-
Felix Fietkau authored
Signed-off-by:Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39150
-
Gabor Juhos authored
The hardware supports large ethernet frames. Override the maximum frame length and packet lenght mask in the platform data to allow to use large MTU on the ethernet interfaces. Limit the feature to AR934x SoCs for now. It should work on some other SoCs as well, but those has not been tested yet. Signed-off-by:Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39149
-
Gabor Juhos authored
The currently used bitmask of the maximum frame length field is wrong for both models. On AR724x/AR933x the largest frame size is 2047 bytes, on the AR934x it is 16383 bytes. Make the MTU setup code model specific, and use the correct bitmask for both models. Also change the value to the maximum. Signed-off-by: -
Gabor Juhos authored
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init() and write the correct value into that from the ag71xx_open() and ag71xx_fast_reset() functions. Also recalculate the RX buffer size based on the actual maximum frame length value to optimize memory allocation. Additionaly, disallow to change the MTU value while the interface it running. Signed-off-by: -
Gabor Juhos authored
Signed-off-by: -
Gabor Juhos authored
This will allow to use SoC specific values for both. Signed-off-by: -
Gabor Juhos authored
The currently used bitmask is not correct for all SoCs. Introduce a new field in struct ag71xx and store the bitmask in that. Use the current value for now, it will be adjusted for each SoCs in further patches. Aslo use the new field directly in the ag71xx_rx_packets and ag71xx_hard_start_xmit() functions and remove the ag71xx_desc_pktlen() helper. Signed-off-by: -
Imre Kaloz authored
Signed-off-by: -
Imre Kaloz authored
Signed-off-by:
-
- Dec 19, 2013
-
-
Felix Fietkau authored
Signed-off-by: -
Felix Fietkau authored
Signed-off-by: -
Luka Perkov authored
Signed-off-by:Luka Perkov <luka@openwrt.org> SVN-Revision: 39135
-
Luka Perkov authored
Without it in some occasions oops is shown on network restart. Problem was noticed on imx6 targed. Signed-off-by: -
Luka Perkov authored
The previous patch was not the proper fix for PCI devices that require io resources. The new patch is the proper fix backported from mainline. Signed-off-by:Tim Harvey <tharvey@gateworks.com> SVN-Revision: 39133
-
- Dec 18, 2013
-
-
Jo-Philipp Wich authored
The instance_config_move() function in the procd instance managing code is missing a blobmsg_list_move() call to update the tracked file items with the newly calculated checksums in case of a file change. Without that change, services are always reloaded after the first change to a tracked file regardless of whether there are any subsequent changes or not. Add a missing instance of blobmsg_list_free() as well. Signed-off-by: -
Jo-Philipp Wich authored
SVN-Revision: 39131
-
- Dec 17, 2013
-
-
Gabor Juhos authored
Now that the switch works correctly we can enable the images for this board. Flashing from the factory firmware, the factory failsafe loader and sysupgrade was tested successfully. Signed-off-by:
Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4617/ Signed-off-by:
-
Gabor Juhos authored
Now that the switch is working correctly I had the chance to actually test the LED config. Signed-off-by:
-
Gabor Juhos authored
The bootloader on the WD My Net N750 disables the ports on it's internal AR8327N switch by powering them down. The stock firmware then brings the ports back up again by starting the auto negotiation process on each port. This fix implements just that. Signed-off-by:
-
Gabor Juhos authored
This enables us to add fixups to the board specific code for boards that require special treatment of PHYs on mdio bus reset. Signed-off-by:
-
Gabor Juhos authored
This enables us to modify the ag71xx_mdio_platform_data from within the board support files. Signed-off-by:
-
Felix Fietkau authored
busybox: add back support for top-level menuconfig based config overrides (can be used by custom packages to alter the config) Signed-off-by: -
Jonas Gorski authored
Don't call gpio_keys_remove recursively. Setting the platform data to NULL triggered an oops on the second iteration, so there was no infinate loop. Signed-off-by:Jonas Gorski <jogo@openwrt.org> SVN-Revision: 39124
-
Jo-Philipp Wich authored
Since the removal of the busybox menuconfig entries, the init scripts for cron, telnet and ntp are not packaged anymore. Unconditionally ship them from now on. Signed-off-by: -
Jo-Philipp Wich authored
The firewall3 implementation as well as the shell implementation predating it used to process the tcp_ecnoption as boolean while it actually is an integer. Change the code to parse tcp_ecn as integer. Signed-off-by: -
Gabor Juhos authored
Currently, the AG71XX_RX_PKT_SIZE value limits the received frame size to 1514/1516 bytes with/without a VLAN header respectively. However the hardware limit is controlled by the value the AG71XX_REG_MAC_MFL register which contains the value of the max_frame_len field. Compute the RX buffer size from the max_frame_len field to get rid of the 1514/1516 byte limitation. Also remove the unused AG71XX_RX_PKT_SIZE definition. Signed-off-by: -
Gabor Juhos authored
This allows to change the value dynamically. Signed-off-by: -
Felix Fietkau authored
Signed-off-by: -
Felix Fietkau authored
Signed-off-by: -
Gabor Juhos authored
This will allow to use different values for the different SoCs. Signed-off-by: -
Gabor Juhos authored
The ar7240_probe function uses the network device name in the kernel log messages, however the name is not yet initialized when the ar7240_probe function is called. Use the mdio bus name in the messages to avoid ugly log lines like the following one: eth%d: Found an AR7240/AR9330 built-in switch Reported-by:
Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by:
-
Gabor Juhos authored
The ag71xx debugfs code uses the network device name for the device specific debugfs directory. Since r38689 'ar71xx: ag71xx: fix a race involving netdev registration' the debugfs initialization happens before the ethernet device gets registered and the network device name contains 'eth%d' at this point. If the board setup code registers multiple ag71xx devices, the debugfs code tries to create the device specific dir with the same name which causes an error like this: eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] ag71xx: probe of ag71xx.0 failed with error -12 Use the device name for the debugfs directory to avoid the collisions. Also add an error message and change the return code if the debugfs_create_dir call fails. Reported-by:
-
Felix Fietkau authored
Signed-off-by: -
Luka Perkov authored
Some of the Gateworks Ventana boards have CAN bus support, therefore we will install the userspace utils. Signed-off-by: -
Luka Perkov authored
All Gateworks Ventana boards have a Gateworks System Controller which emulates the following: - ds1672 RTC - pca953x GPIO expander - hardware monitor - at24 eeprom Signed-off-by: -
Luka Perkov authored
Signed-off-by:
-
Luka Perkov authored
Signed-off-by: -
Luka Perkov authored
Signed-off-by:
-
