Skip to content
Snippets Groups Projects
Select Git revision
  • master default protected
  • v17.01.1
  • v17.01.0
  • v17.01.0-rc2
  • v17.01.0-rc1
  • reboot
6 results
Search by author
  • Any Author
  • Johannes Rudolph Johannes Rudolph PowerPan
1 author
  1. Feb 05, 2017
    • Kristian Evensen's avatar
      ramips: add support for Sanlinking D240 · bb7068f2
      Kristian Evensen authored 
      The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html

) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: default avatarKristian Evensen <kristian.evensen@gmail.com>
      bb7068f2
  3. Jan 31, 2017
    • FUKAUMI Naoki's avatar
      ramips: add support for Buffalo WCR-1166DS · 6b0b526a
      FUKAUMI Naoki authored 
      
Buffalo WCR-1166DS is a small wireless router with

 - MT7628AN + MT7612E
 - 64MiB DDR2 SDRAM
 - 16MiB SPI flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 2x 10/100M ethernet switch
 - 8x programmable LED
 - 3x button
 - UART pad on PCB (J2: 3.3V, GND, TX, RX)

factory image can be installed via stock web UI.

due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.

Signed-off-by: default avatarFUKAUMI Naoki <naobsd@gmail.com>
      6b0b526a
  5. Jan 18, 2017
  7. Jan 15, 2017
    • Lazar Demin's avatar
      ramips: Added Onion Omega2 and Omega2+ · ab90f15c
      Lazar Demin authored 
      This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io

)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: default avatarLazar Demin <lazar@onion.io>
      ab90f15c
  9. Jan 13, 2017
    • Andrew Yong's avatar
      ramips: add support for VoCore2 · 3f31029b
      Andrew Yong authored 
      
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: default avatarAndrew Yong <me@ndoo.sg>
      3f31029b
  11. Dec 24, 2016
  13. Dec 22, 2016
  15. Nov 23, 2016
  17. Nov 21, 2016
  19. Nov 18, 2016
  21. Nov 17, 2016
    • Jasper Scholte's avatar
      ramips: add support for Sitecom WLR-6000 · 3d680c57
      Jasper Scholte authored 
      
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.

The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.

The stock firmware uses the following mac addresses:

LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5:   00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)

Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

2.4GHz: 00:0C:F6:AA:BB:D8
LAN:    00:0C:F6:AA:BB:D9
WAN:    00:0C:F6:AA:BB:DA
5 GHz:  00:0C:F6:AA:BB:DC

The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.

There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.

Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.

Signed-off-by: default avatarJasper Scholte <NightNL@outlook.com>
Signed-off-by: default avatarMathias Kresin <dev@kresin.me>
      3d680c57
    • Dominik Menke's avatar
      ramips: add support for Digineo AC1200 Pro · 8b65fef1
      Dominik Menke authored 
      
This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash.

Signed-off-by: default avatarDominik Menke <dom@digineo.de>
      8b65fef1
  23. Nov 08, 2016
    • Roger Pueyo Centelles's avatar
      ramips: Add support for Wavlink WL-WN575A3 · 5f6e9485
      Roger Pueyo Centelles authored 
      
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: default avatarRoger Pueyo Centelles <roger.pueyo@guifi.net>
      5f6e9485
  25. Nov 02, 2016
    • Andrew Yong's avatar
      ramips: add support for MikroTik hEX v3 (RB750Gr3) · faf94d92
      Andrew Yong authored 
      The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot

 - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: default avatarAndrew Yong <me@ndoo.sg>
      faf94d92
  27. Oct 15, 2016
    • YuheiOKAWA's avatar
      ramips: add support for Planex VR500. · 4050cfeb
      YuheiOKAWA authored 
      
SOC:	MT7621A
RAM:	256MiB
NOR:	MX25L51245G

Non Wireless Router.

Issue: soft reboot problem. SPI Flash do not exit 4byte address mode.

Signed-off-by: default avatarYuhei Okawa <tochiro.srchack@gmail.com>
      4050cfeb
    • Mathias Kresin's avatar
      ramips: move edimax images to the new build code · e7ec5df3
      Mathias Kresin authored 
      
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.

Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.

Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.

Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.

Signed-off-by: default avatarMathias Kresin <dev@kresin.me>
      e7ec5df3
  29. Oct 04, 2016
  31. Sep 27, 2016
  33. Sep 09, 2016
  35. Aug 10, 2016
  37. Jul 11, 2016
  39. Jun 22, 2016
  41. Jun 13, 2016
  43. Jun 01, 2016
  45. May 12, 2016
  47. May 10, 2016
  49. Apr 26, 2016
  51. Apr 21, 2016
    • John Crispin's avatar
      ramips: Add support for ZBT WG3526 · 30fbc1a4
      John Crispin authored 
      
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.

v1->v2:
* Remove some references to 2626 that I had missed in the dts.

v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.

Signed-off-by: default avatarKristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 49213
      30fbc1a4
    • John Crispin's avatar
      ramips: add support for ELECOM WRH-300CR · 37b50fdb
      John Crispin authored 
      
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.

it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.

Signed-off-by: default avatarYuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: default avatarFUKAUMI Naoki <naobsd@gmail.com>

SVN-Revision: 49211
      37b50fdb
  53. Apr 20, 2016
  55. Mar 16, 2016