If you're using Chrony or NTPD you don't want the busybox NTP server
as well.  Make it's installation truly conditional.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [simplify]

Intel(R) 82576 is an adapter which supports SR-IOV. Thus the host can
assign Virtual Functions (VFs) to different VMs by the PCI-E Passthrough
(e.g. VFIO for KVM), to gain different advantages (performance, VF to VF
communications, host kernel offload, etc.).

The driver of the passthroughed VFs is the igbvf (igb is NOT
compatible).

This is essential for VM guests, to enable them to utilize this feature.

Signed-off-by: Ye Tao <tydus@hongo.wide.ad.jp>

3d9f406 rework IPv6 dns address selection (FS#635)
bc6c3ac ndp: keep an exact copy of IPv6 interface addresses
6eb1e01 ndp: code cleanup
eea7d03 rework IPv6 address dump logic
24d21c7 ndp: add syslog debug tracing

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

Some of our local patches have been accepted upstream. And there are
some more relevant changes (mostly for rt2800usb). Import them and
rebase our remaining local patches on top.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.

Signed-off-by: Karl Vogel <karl.vogel@gmail.com>

20c16fc cmake: Make blockd link against libjson-c
92b4c2c libfstools: add basic documentation of mount functions

Signed-off-by: John Crispin <john@phrozen.org>

This is a 3rd party chipset which is not present on all Intel
reference designs, so make it a module rather than baked in (this
will also alleviate conflicts with drivers which also detect some
of the same chipsets).

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

A lot of Ivybridge and Haswell servers have the 82598/82599 Ethernet
controllers.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

These are recommended practices by REC-22 and REC-24 of RFC6092:
"Recommended Simple Security Capabilities in Customer Premises Equipment
(CPE) for Providing Residential IPv6 Internet Service"

Fixes FS#640

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

ath10k tries to fetch board id via otp, but that fails for many chips
like QCA988x, QCA9984 etc. Recent commit cc189c0b removed the earlier
hack that had allowed QCA radios to work, as that hack was incompatible
with the new wifi chips being introduced to the source tree.

Restore functionality for the existing wifi chips by modifying the
return value of the 'board id via otp' function to a value that is recognised
as a harmless error, so that name evaluation continues by using the board file.

Patch originally suggested by Christian Lamparter in forum discussion.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

F2FS depends on the crc32_generic module (NOT crc32c_generic)

Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>

This is needed for F2FS support (it depends on crc32_generic,
not crc32c_generic).

Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>

With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>

- remove unused code within 500-ar9_vr9.patch
- fixed return of IFX_ERROR (solves SIGSEGV in asterisk at failure)
- align it a bit with 400-falcon.patch
- remove 600-kernel-4.9.patch since changed parts
  are removed during cleanup

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>

Make scan output useful for 802.11s meshes. The common print_ssid function
is used, so this doesn't add any additional code.

Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

modify 500-ar9_vr9.patch from
commit 29367aac ("lantiq: ltq-vmmc add support for ar9-vr9")

- remove unused dependencies to external watchdog functions
  (wdog setup is already disabled)
- using header file from kernel (asm/vpe.h) instead patched file (vpe.h)
- cleanup whitspace warning

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>

Do not select the qca988x by default as soon as kmod-ath10k is
selected. We do support more ath10k chips than the qca988x in the
meantime, so this dependency doesn't make sense any longer.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Fixes FS#637

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

0463b05 dhcpv6: rebind capability support in reconfigure message (rfc6644)
53767fc dhcpv6: respect renew end point when handling reconfigure message
dd892e2 dhcpv6: calculate T1, T2 and T3 in a more sane manner
8a6ca6e md5: use libubox md5 library as local implementation
89822de dhcpv6: don't return renew msg in case of invalid msg type in reconfigure msg
4160c0e treewide: align coding style

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lowr limits than the CTLs
of the user configured regdomain.

To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

If a device uses the default EEPROM code, typically only the main CTLs
are valid, and they do not apply properly when switching to a different
regulatory domain. If the regdomain deviates from the EEPROM one, force
the world roaming regdomain to ensure that power limits are sane

Signed-off-by: Felix Fietkau <nbd@nbd.name>

The original build error in 'more' seems to be gone

Signed-off-by: Felix Fietkau <nbd@nbd.name>

The build dependency is unconditional, and some components might fail if
ncurses is not available

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Update util-linux to 2.29.2
Remote 0001-fix-uClibc-ng-scanf-check.patch as it's been merged upstream.
Refresh patches
Change ncurses to ncursesw to fix compilation and avoid confusion

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove faulty dependency changes]

This reverts commit eac1a548.

This patch caused the builders to blow up.

Signed-off-by: John Crispin <john@phrozen.org>

Update f2fs-tools to 1.8.0
Refresh patches
Remove selinux patch, use configure argument instead.
Switch to xz tarball
Adjust url to avoid redirects

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>

Use device tree based model string

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.

This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io

.

Note, this commit is just the initial board support hence the
following are not expected to work yet:
 * WiFi
 * Bluetooth
 * 6lowpan
 * Audio
 * Mikrobus uarts, user leds (clock dependency of 6lowpan chip)

The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.

Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

This will be used to replace all those nasty board specific scripts
that do basically the same thing

Signed-off-by: Felix Fietkau <nbd@nbd.name>

It is useful for creating static ARP entries.
Adds about 1.9 KiB after gzip on MIPS.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

In the drv_mac80211_setup function, mac80211_interface_cleanup
is called to ask the kernel to delete all existing interfaces
for the phy that is being configured via netlink.

Later in the first function, mac80211_prepare_vif is called to
set up the new interfaces as required.

But sometimes, when mac80211_prepare_vif (and so the relevant
`iw phy x interface add y` command) runs, the kernel might still
be cleaning up the old interface with the same ifname. It usually
takes very few time to do that; possibly a few milliseconds of
sleep in the script after detecting this error condition could be
enough, but the busybox sh does not support sub-second sleep
intervals.

When this happens, iw obviously fails to create the new interface;
and the following message is printed in the system log, followed by
subsequent failure messages from hostapd in case this would have been
an AP interface.

Tue Mar 14 04:21:57 2017 daemon.notice netifd: radio1 (2767): command failed: Too many open files in system (-23)

This was a long-standing issue existing since at least OpenWrt Backfire,
and today I finally managed to debug and (hopefully) solve it.
It was happening very few times on most devices; but it was happening
a lot more frequently on fast platforms with multiple radios, such as
the powerpc-based dual-ath9k-radio tl-wdr4900-v1.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

On the ath10k-devel ML Michael Kazior stated:

"board-2 is a key-value store of actual board files.
Some devices, notably qca61x4 hw3+ and qca4019 need
distinct board files to be uploaded. Otherwise they
fail in various ways." [0].

Later on Rajkumar Manoharan explained:

"In QCA4019 platform, only radio specific calibration
(pre-cal-data) is stored in flash. Board specific contents
are read from board-2.bin. For each radio appropriate board
data should be loaded. To fetch correct board data from
board-2.bin bundle, pre-cal/radio specific caldata should
be loaded first to get proper board id.

|My understanding until now was that:
|
| * pre-cal data + board-2.bin info == actual calibration data

Correct." [1].
The standard board-2.bin from the ath10k-firmware-qca4019
barely works on the RT-AC58U. Especially 5GHz clients fail
to connect at all and if they do, they have very low
throughput even right next to the router.

Currently, the solution for this problem is to supply a
custom board-2.bin for every device.

To implement this feature, this method makes use of:
Rafał Miłecki's "base-files: add support for overlaying
rootfs content". This comes with a few limitations:
1. Since there can only be one board-2.bin at the right
   location, there can only one board overwrite installed
   at any time. (All packages CONFLICT with each other.
   It's also not possible to "builtin" multiple package.)

2. updating ath10k-firmware-qca4019 will also replace
   the board-2.bin. For this cases the user needs to
   manually reinstall the wifi-board package once the
   ath10k-firmware-qca4019 is updated.

To create the individual board-2.bin: Use the ath10k-bdencoder
utility from the qca-swiss-army-knife repository:
<https://github.com/qca/qca-swiss-army-knife

>
The raw board.bin files have to be extracted from the
vendor's source GPL.tar archieves.

Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

Adds tools to access tffs3 and pre-calibration data required for ipq4019
based FritBoxes.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

With this patch, the nand.sh script no longer overwrites
CI_KERNELPART and CI_UBIPART if they have been set before.

This allows platforms specify alternative values for these
variables.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

This patch enables the ATH10K_AHB support for the QCA4019
devices on the AHB bus.

This patch also removes 936-ath10k_skip_otp_check.patch
because it breaks the AHB device identification.
"Patch is wrong. I find it frustrating OpenWRT/LEDE doesn't
try to work with upstream on ixing these things right."

[1] <https://www.mail-archive.com/ath10k@lists.infradead.org/msg05896.html

>

It also limits ath10k memory hunger (This is a problem with 128MiB RAM)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>