Signed-off-by: Mirko Vogt <mirko-openwrt@nanl.de>

This device has 2 TRX partitions (main one and failsafe one) and Linux
may not detect them properly failing to run userspace.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

mt2701 is an earlier version of the ip core, so use that compat string as
baseline.

Signed-off-by: John Crispin <john@phrozen.org>

All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.

Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.

The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.

Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Use the standard off_t type instead of loff_t

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Even when the disk uses 4k blocks, the partition table still uses units
of 512 byte sectors. Always use ibs=512 for the offsets

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>

- remove CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
- enable jffs2 support
- fix sysupgrade

Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>

Signed-off-by: Sergey Sergeev <adron@yapic.net>

stage u-boot images in KERNEL_BUILD_DIR for building images
always select uboot-mxs

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

If the base-files package is not selected, we will fail executing the
very first postinst script:

make[3]: Leaving directory `/local/users/fainelli/openwrt/trunk'
cp -fpR
/local/users/fainelli/openwrt/trunk/build_dir/target-arm_xscale_musl-1.1.15_eabi/root-orion
/local/users/fainelli/openwrt/trunk/build_dir/target-arm_xscale_musl-1.1.15_eabi/root.orig-orion
./usr/lib/opkg/info/busybox.postinst: line 3:
/local/users/fainelli/openwrt/trunk/build_dir/target-arm_xscale_musl-1.1.15_eabi/root-orion/lib/functions.sh:
No such file or directory
./usr/lib/opkg/info/busybox.postinst: line 4: default_postinst: command
not found
postinst script ./usr/lib/opkg/info/busybox.postinst has failed with
exit code 127
make[2]: *** [package/install] Error 1

Check for the existence of lib/functions.sh, and if it does not exist,
just bail out gracefully.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

If only a single opkg control file exists (which can happen with
CONFIG_CLEAN_IPKG), grep would not print the file name by default. Instead
of forcing it using -H, we just switch to -l (print only file names) and
get rid of the cut.

Add -s to suppress an error message when no control files exist.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

Require-User is handled by /etc/uci-defaults/13_fix_group_user on first
boot, so we need to keep these when removing all opkg data with
CONFIG_CLEAN_IPKG.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

There was a bug in brcmfmac patch that could result in treating random
memory as source of country codes.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

This reverts commit c296ba83.
According to several reports, the issues with the airtime fairness
changes are gone in current versions.
It's time to re-apply the patch now.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

The ZyXEL NSA310 device is a Kirkwood based NAS:

- SoC: Marvell 88F6702 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: Realtek (over pcie)
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II port (1 internal and 1 external)
- 2 USB 2.0 ports (1 front and 1 back)
- Smart fan

The stock u-boot cannot read ubi so it should be replaced with the
LEDE/OpenWRT's u-boot or with a u-boot from here
https://github.com/mibodhi/u-boot-kirkwood



This device's boot ROM supports "kwboot" tool
(in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared)
that sends an uboot image to the board over serial connection, it is very easy to unbrick.

The stock bootloader can use usb and read from FAT filesystems,
so the installation process is simple, place the uboot file on a USB flashdrive
formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL
to the board and write the following commands in the bootloader console:

usb reset
fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin
nand write 0x1000000 0x00000 0x100000
reset

Now you are rebooting in the new u-boot, write this in its console to install the firmware:

usb reset
fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin
nand erase.part ubi
nand write 0x2000000 ubi 0x600000

If your firmware file is bigger than 6 MiBs you should write its size in hex
instead of 0x600000 above, or remove that number entirely (it will take a while in this case).

If you are using another uboot that can read ubi, set mtdparts like this

mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)

And set your bootcmd to be like this

bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000

Then you can install the firmware as described above.

After you installed (or configured) the u-boot for booting the firmware,
write the device's mac address in the ethaddr u-boot env.
The MAC address is usually on a sticker under the device (one of the two codes is the serial),
it should begin with "107BEF" as it is assigned to ZyXEL.

write in the u-boot console (use your MAC address instead of the example)

setenv ethaddr 10:7B:EF:00:00:00
saveenv

to save the mac address in the u-boot.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>

accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>

Signed-off-by: Hans Geiblinger <cybrnook2002yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately

Signed-off-by: Felix Fietkau <nbd@nbd.name>

support for pxa has been gone for a long time now

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

this commit allows to make a standalone u-boot for nsa310b.

While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>

Upon first invocation, the ccache program will create the required directory
hierarchy so there is no point in shipping these empty directories.

Removing those paths also avoids shipping dangling symlinks in case the
directories got linked elsewhere, e.g. into a shared global cache.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Fixes build issues when there is nothing to do on the compile step (e.g.
with unselected packages).

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>