This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/

 (patches 110-111)

We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45663

This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.

It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45662

ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.

On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.

As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45661

This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45658

Signed-off-by: Catrinel Catrinescu <cc@80211.de>

SVN-Revision: 45656

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45655

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45653

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45652

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45650

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45648

Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome

>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 45647

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45646

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45645

There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 45643

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45640

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45639

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45638

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45637

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45636

Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45635

Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45634

Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861



I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
  1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
  2) must init GMAC0 before GMAC1

That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.

An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.

2) Possible consequence of no longer explicitly setting ethernet duplex/speed.

Review: With this patch, my ethernet and wireless works.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45633

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45632

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45631

It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45630

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45629

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45627

It has been broken since the new ath10k firmware introduced in r44656.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 45624

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45621

We were calculating wrong offset, NVRAM wasn't found and OpenWrt didn't
boot.

Fixes: 9019803 ("brcm47xx: backport BCM47XX arch patches (clean NVRAM code, later init)")
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45618

Also refresh one patch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45601

This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45599

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45598

This will make these files much more maintainable.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45597

The ability to read MAC addresses from MTD is useful for other targets besides ramips and lantiq as well.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45596

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45589

Moved board to the right magic case.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 45588

INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.

So just disable it for everyone.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45584

This was a remnant of an old version.

Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45583

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45582