Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45995

On bcm53xx we still need usb-ohci to support USB 1.1 devices and it
obviously needs bcma-hcd.ko that will init controller and register
platform device.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45994

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45992

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45990

Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>

SVN-Revision: 45988

This one cannot possibly work, as it depends on cfg80211, which is built
out of tree.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45985

Besides source.tgz, 001-elfutils-portability.patch (provided by upstream
project) where updated.

Other patches where updated to fix hulk warnings and minor conflicts.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>

SVN-Revision: 45984

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 45983

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 45982

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 45981

pad-to can be used in a pipe to pad the image to a specific chunk-size.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 45980

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 45979

Currently "make clean" only clears the build_dir/target*, but leaves
staging_dir/target* intact. "make clean" should also clean the
staging_dir/target* directories, as in the current situation some old
packages or libraries may be linked into the firmware from staging_dir
despite a "make clean".

The patch reorganises clean / dirclean functionality so that
* "make clean" also clears the staging_dir/target* in addition to
build_dir/target*.
* "make dirclean" clears toolchain and host(=tools) directories from both
build_dir and staging_dir

signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

SVN-Revision: 45973

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45972

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45971

AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.

Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.

The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 45970

elfutils is required by perf. So we'll move this package from
packages.git and make it part of the core distribution.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45969

bzip2 is required by elfutils, itself required by perf. So we'll move
this package from packages.git and make it part of the core
distribution.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45968

argp-standalone is required by elfutils, itself required by perf. So
we'll move this package from packages.git and make it part of the core
distribution.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45967

Hello,

I found out that in some rare cases grep can treat Makefile as a binary file. That happened to me on UTF-8 Gentoo if Makefile contained a character which was from extended ASCII table.
Without this patch the output of the grep command in the $(FILELIST) target is not valid (contains line "Binary file matches") and following commands fail to create feed index file.

Best Regards,
Martin Strbacka

Signed-off-by: Martin Strbacka <martin.strbacka@nic.cz>

SVN-Revision: 45966

This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45965

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45964

The *u-boot-initramfs* images are not ITB/FIT images but are rather
supposed to be loaded to RAM and jumped-into.
To avoid confusion, change the file extension from itb to bin.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 45963

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 45962

This is for security precautions.  As persist_tun and persist_key are
already there, this should not cause compatibility issue.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 45961

As reported in ticket #19104, auth_retry takes a <type> argument with 3
choices: none, nointeract, interact.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 45960

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45959

In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes #19751, bug introduced in #45624

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 45958

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45957

They are of 32-bit little endian integers.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 45956

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 45955

The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.

The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.

The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.

Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 45954

- fix iconv detection because it adds host paths
- disable python detection (host python-config is found)

iconv issue is reported by buildbot config.log + replicated locally
see config.log in logs.tar.gz
python issue observed locally on Arch Linux

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 45953

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45952

Signed-off-by: Steven Barth <steven@midlink.org>

SVN-Revision: 45950

Signed-off-by: Steven Barth <steven@midlink.org>

SVN-Revision: 45949

Adds PPP unnumbered support via the parameter unnumbered which points to a logical OpenWRT interface.
The PPP proto shell handler will "borrow" an IP address from the unnumbered interface (if multiple
IP addresses are present the longest prefix different from 32 will be "borrowed") for which a host
interface dependency will be created. Due to the host interface dependency the PPP unnumbered interface
will only "borrow" an IP address from an interface which is up.
The borrowed IP address will be shared as local IP address by the PPP daemon and no other local IP
will be accepted from the peer in the IPCP negotiation.

A typical use case is the usage of a public IP subnet on the Lan interface which will be shared
by the PPP interface as local IP address.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

SVN-Revision: 45948

Signed-off-by: Steven Barth <steven@midlink.org>

SVN-Revision: 45947

Signed-off-by: Steven Barth <steven@midlink.org>

SVN-Revision: 45946

When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.

Fixes #19836.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45945