* make clock delay configurable
* make read,write commands configurable
* use u16 for member and untag fields

SVN-Revision: 29677

SVN-Revision: 29676

The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.

This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.

Patch-by: Dave Taht <dave.taht@gmail.com>

SVN-Revision: 29675

It is based on patches from the linux-longsoon-community git tree:
http://dev.lemote.com/cgit/linux-loongson-community.git/

Now the kernel can use the command line parameter from kexec-tools.

Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped
before executing the new kernel). Compile tested with lantiq (3.1.4)
and brcm47xx (3.0.12).

SVN-Revision: 29674

SVN-Revision: 29672

openssl: bump to v1.0.0f (CVE-2011-4108, CVE-2011-4576, CVE-2011-4577, CVE-2011-4619, CVE-2012-0027)

SVN-Revision: 29670

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 29669

SVN-Revision: 29668

SVN-Revision: 29667

SVN-Revision: 29666

SVN-Revision: 29664

SVN-Revision: 29663

The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.

SVN-Revision: 29662

SVN-Revision: 29660

SVN-Revision: 29659

These models are based on the AP99 reference board,
and uses the AR7241 SoC.

SVN-Revision: 29658

SVN-Revision: 29657

SVN-Revision: 29656

SVN-Revision: 29655

SVN-Revision: 29654

SVN-Revision: 29653

Also use the system LED for diagnostic.

SVN-Revision: 29652

This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.

I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020



USB is working and has been tested with USB mass storage and USB UMTS
stick.

Wifi also seems to work.

Ethernet is working too.

Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>

SVN-Revision: 29651

Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>

SVN-Revision: 29650

Signed-off-by: Antonio Quartulli <ordex@autistici.org>

SVN-Revision: 29649

Signed-off-by: Antonio Quartulli <ordex@autistici.org>

SVN-Revision: 29648

om2p-watchdog package is OM2P specific. However a similar watchdog
mechanism exists on OM1P as well. This new package wants to substitute
om2p-watchdog with a new one which is suitable either for OM1P and OM2P.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>

SVN-Revision: 29647

SVN-Revision: 29646

This patch adds the CT target for conntrack (enables manipulation of
conntrack events and supercedes NOTRACK) as well as the TTL/HL target and
match.

SVN-Revision: 29645

SVN-Revision: 29643

backport upstream commit e1738bd9cecc5c867b0e2996470c1ff20f66ba79 to affected kernels (#9802) commit 8efa88540635 (sch_sfq: avoid giving spurious NET_XMIT_CN signals) forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a packet (from another flow) was dropped, leading to various problems.

SVN-Revision: 29642

SVN-Revision: 29637

SVN-Revision: 29636

SVN-Revision: 29635

SVN-Revision: 29634

SVN-Revision: 29633

SVN-Revision: 29631

SVN-Revision: 29630

SVN-Revision: 29629

SVN-Revision: 29628