Fixes #758

Signed-off-by: Paul Spooren <paul@spooren.de>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

It was originally only enabled for the "32" subtarget along with the
"usb" feature which is now also shared by the "64" target

This should fix the phase1 build of armvirt/64

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.

Ref: https://github.com/openwrt/luci/issues/1086



Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)

The basic_rate option and supported_rates option are filtered based on this.

The rationale for the change, stronger now than in 2014, can be found in:

https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx



The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.

Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]

When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.

Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.

This issue can be reproduced with following /etc/config/wireless:
config wifi-device  radio0
        option type     mac80211
        option channel  1
        option hwmode   11g
        option path     'virtual/uccp420/uccwlan'
        option htmode   'none'

config wifi-iface 'ap'
        option device 'radio0'
        option encryption 'none'
        option mode 'ap'
        option network 'ap'
        option ssid 'MyTestNet'
        option encryption none

config wifi-iface 'sta'
       option device radio0
       option network sta
       option mode sta
       option ssid TestNet-5G
       option encryption psk2
       option key 12345

This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.

Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]

Commit 2036ae4 (base-files: support hostname and ntp servers through board.d)
was supposed to implement these procedures but lacked the required changes
to uci-defaults.sh.

Add the missing procedures now to fix config generation on targets relying
on hostname or NTP server presetting.

Fixes FS#754.

Reported-by: Cristian Morales Vega <cristian@samknows.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Changes since last version

    04e279e pkg_alternatives: use ERROR level for symlink failure

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

When busybox customisation is enabled, we should depend on config
symbols CONFIG_BUSYBOX_CONFIG_xxx to form alternatives specs

Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Otherwise ipkg packages may wrongly take on alternatives specs of
another package sharing the same package Makefile

Fixes FS#753

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Signed-off-by: John Crispin <john@phrozen.org>

A number of small tweaks & improvements on the way to a final release.
Most notable:

Improve DHCPv4 address-in-use check.
Remove the recently introduced RFC-6842 (Client-ids in DHCP replies)
support as it turns out some clients are getting upset.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

They will not be in conflict anymore ;)

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Changes since last version

    546bc72 pkg: alternatives support
    7a96972 libbb: xreadlink: fix memory leak on failure case
    3f13edd pkg_run_script: use pkg->dest in half installed case

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

It's a list of specs of the following form seprated by commas to
describe alternatives provided by this package

    <prio>:<path>:<altpath>

<path> will be a symbolic link to <altpath> of the highest <prio>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.

Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>

With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.

Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>

arc-2016.09 is the most recent toolchain for ARC cores and
it is based on top of upstream Binutils 2.27 and GCC 6.2.1.

With updated major version of GCC we copied all GCC 6.x patches
for ARC as well as Bintils 2.27 patches.

Note that toochain sports ARCv4 ABI and so must be used
with 4.8+ Linux kernels. Even though it will build v4.4 kernel
perfectly fine on attempt to run user-space apps they won't
work with older kernel. That said previuosly sent RFC patches with
Linux kernel update are required:
 [1] https://patchwork.ozlabs.org/patch/726686/
 [2] https://patchwork.ozlabs.org/patch/726687/



Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>

DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.

In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.

On building all ends-up with:
---------------------->8------------------
  Kernel: arch/arm/boot/Image is ready
  Kernel: arch/arm/boot/zImage is ready
  Building modules, stage 2.
  MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------

This was affecting Lede in case of CONFIG_ALL_KMODS=y.

The patch is already scheduled for v4.12 and once it is backported to
4.9.y it must be removed from here.

Note this patch makes sense not only for ARC instead it fixes
a generic issue which may affect more arches and platforms thus
putting it in "generic/" folder.

Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [patch rename]

Signed-off-by: Felix Fietkau <nbd@nbd.name>

It's the best method I know (so far) to refresh
the kernel config to a default state.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>

Since commit:
http://github.com/torvalds/linux/commit/7120438e5d82f445acbfe131a1b58eab7e83fa33



Seems that fsl_rstcr_restart() has been converted
to a reset handler and dropped as hook/callback.

Apply the same to the `tl_wdr4900_v1` target.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>

Re-applied patches:
001-powerpc-85xx-add-gpio-keys-to-of-match-table.patch
100-powerpc-85xx-tl-wdr4900-v1-support.patch

Dropped patch:
200-spi-fsl-espi-preallocate-local-buffer.patch
now part of kernel upstream hash
https://github.com/torvalds/linux/commit/1423877b73ed5f4982eaba8bed359605b9918a2b



Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>

Signed-off-by: Bastian Köcher <git@kchr.de>

Keep them disabled by default to avoid pulling in extra kernel bloat

Signed-off-by: Felix Fietkau <nbd@nbd.name>

It's disabling thumb for the whole omap3 family.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

Even it's unknown if it's booting with thumb, because the lack of hardware.
Enable it for now, so the build succeed, because without thumb it can not fit
into spl.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

Early SoC versions with an ECO of 1 required the gpio reset.
Mass production SoCs no longer need this work around.

Signed-off-by: John Crispin <john@phrozen.org>

9268ca6 ndp: don't trigger IPv6 ping when neighbor entry is invalid
2b3355f ndp: fix adding proxy neighbor entries
7dff5b4 ndp: fix wrong interface name in syslog message
a54afb5 dhcpv6-ia: Fix segfault when writing DHCPv4 leases in state file
c0e9dbf ubus: don't segfault when there're no leases

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

Configuring dhcp_option as an option does not allow the usage of white
spaces in the option value; fix this by supporting dhcp_option as a list
config while still supporting the option config to maintain backwards
compatibility

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

This is required to fully support a number of 32bit x86 systems equipped
with more than one GB ram, e.g. certain Atom CPU machines.

Ref: https://forum.lede-project.org/t/17-01-1-x86-doesnt-detect-all-of-the-ram/3295



Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Add the changes suggested by FS#716 to fix the switch driver initialization
on the ZTE Q7.

Also remove the `pinctrl-names` field obsoleted by the changes.

Reported-by: Harry Lau <harrylwc@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

When invoking "nslookup_lede" with a domain argument and without explicit
query type, issue both A and AAAA queries and display the resulting IP
addresses in a numbered list style, similar to how the old BusyBox nslookup
used to output the records.

This is required for compatibility with certain scripts.

Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1



Signed-off-by: Jo-Philipp Wich <jo@mein.io>

The ":*" optstring syntax was only recently introduced with BusyBox v1.26,
older versions need a corresponding hint in the "opt_complementary" variable
to denote flag values that should be stored as llist entries.

Add the required opt_complementary entry to fix random SIGBUS, SIGILL or
SIGSEGV related crashes on BusyBox 1.25.x when attempting to use the "-q"
flag of the "nslookup_lede" applet.

Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1



Signed-off-by: Jo-Philipp Wich <jo@mein.io>