This patch adds extra parameter to switch LED trigger initialization
functions.  New functionality maintains backward compatibility, so
calling functions without setting new speed_mask parameter works
as expected.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48776

This patch adds speed_mask special file to LEDs connected to switch ports
via 'switch' trigger. It allows to choose which speeds to signal when link
is up. If router has more than one LED per port, they may light up
differently depending on how fast connection is. Default setting is 'all
speeds' so backward compatibility with system scripts (for example uci) is
maintained.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48775

This patch changes swconfig_trig_port_mask_store() handler to utilize
kstrtoul() function instead of call to obsolete simple_strtoul(). Thanks
to this change, new handler takes less memory and makes port_mask special
file accept not only hexadecimal, but also decimal and octal numbers.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48774

Kernel package enables the Freescale CAAM (crypto accelerator and assurance
module, aka SEC4). Sets kernel defaults for ringsize, intc, and debug.

Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>

SVN-Revision: 48773

As indicated in the bug tracker[1], failsafe mode is broken on at least some
devices using the mt7620 switch (and possibly mt7621). The thread explicitly
mentions the Xiaomi MiWifi, and the Nexx WT3020, and an unspecified device
using the mt7621 switch; the issue also applies to the Netgear EX2700.

The problem is that failsafe mode uses eth0, but enable_vlan is always set to 1
by the switch driver. Connecting to and/or pinging the device fails. This patch
fixes the failsafe preinit config, by making sure that vlan support is disabled.
It currently only fixes the switch config on mt7620, but might apply to the
mt7621 as well, so the patch has been designed with this in mind.

A similar (line wrapped) patch was submitted in December by Simon Peter, but never
accepted and/or discussed.

This patch applies to both Chaos Calmer and trunk.

[1] https://dev.openwrt.org/ticket/18768



Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48772

This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.

The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48771

oneshot and timer have the same configuration options, just a different
trigger name.

Signed-off-by: Karl Palsson <karlp@etactica.com>

SVN-Revision: 48770

- insert missing "-" to separate model and version

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>

SVN-Revision: 48769

- it seems there was never a 701N-model build

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>

SVN-Revision: 48768

- remove the suffix (N, ND) to indicate that the image is for all
  WR841-models
- some of these models have a "N"-suffix, others have (ND)-suffix,
  but the boards are the same - only difference is the detachable
  antenna on "D"-models
- discussed this idea to remove the suffix in IRC with jow and Borromini

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>

SVN-Revision: 48767

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 48766

As usual these patches were extracted from:
https://github.com/raspberrypi/linux/commits/rpi-4.4.y



Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 48765

Fixes #21907

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 48764

Before r47933 Bit 1 (first bit) of xTSE Octet 1 (first octet) defaulted
to 1, which allowed T1.413 to operate.

Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>

SVN-Revision: 48763

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48762

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48761

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48760

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48759

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48758

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 48757

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 48756

This patch adds uimage firmware split support for ubi.

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 48755

Seama format has 2 similar headers: container (seal) header and entity
header. The first one has size always set to 0 and doesn't contain MD5
digest.

When dealing with Seama on a flash we deal directly with an entity. You
can see mtdsplit_parse_seama reads from offset 0 and expects entity to
be there. Seama container is used by bootloader / interface only which
extract entity out of it and flash it.

That said we should fix our header struct. This is important as we
calculate possible rootfs offset assuming it may be placed right after
Seama entity. So far calculate offset was always 16B too low.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 48754

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48753

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48752

- Fix typo in board_data partition start address
- Increase board_data partition size in order to exploit all flash size

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>

SVN-Revision: 48751

This adds option to build kernel module and firmware packages
for a Marvell 8686 SPI Wireless device

Signed-off-by: Joseph Honold <mozzwald@gmail.com>

SVN-Revision: 48750

the u2_phy init was missing

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48747

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48746

Signed-off-by: Steven Barth <cyrus@openwrt.org>

SVN-Revision: 48745

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48744

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48743

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 48742

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48741

This patch introduces support of new boards with ARC HS38 cores.

ARC HS38 is a new generation of ARC cores which utilize ARCv2 ISA.
As with ARC770 we're addind support for 2 boards for now:

 [1] Synopsys SDP board (AXS103)
     This is the same base-board as in AXS101 but with
     FPGA-based CPU-tile where ARCHs38 core is implemented.

 [2] nSIM
     Again this is the same simulation engine but configured for
     new instruction set and features of new CPU.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 48740

This change adds support of ARC ISAv2 processors in
OpenWRT toolchain.

In general gcc for ARC may compile code for both ISA versions
simultaneously but libgcc will be built only for default
architecture that's why it's necessary to specify --with-cpu
on gcc configuration.

As for uClibc we need to use different configurations for
different ARC ISAs.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 48739

Signed-off-by: Ben Kelly <ben@benjii.net>

SVN-Revision: 48738

Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr>

SVN-Revision: 48736

Refresh patches and rework Makefile to fetch glibc from release branches
instead of relying on tarballs.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 48735

Upstream is dead and the last available version has multiple open CVEs.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 48734