- Apr 13, 2014
-
-
Gabor Juhos authored
The RB91x boards are suffering from ethernet packet loss after a cold boot. The cause of the problem is that the AR8035 PHYs requires special register settings to work reliably on these boards. Enable the RGMII TX, RX delays and disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register to fix the issue. Signed-off-by:Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 40509
-
Gabor Juhos authored
It will be used on the RB91x boards. Signed-off-by: -
Gabor Juhos authored
Add a patch for the at803x phy driver, in order to be able to configure some register settings via platform data. Signed-off-by: -
Gabor Juhos authored
Signed-off-by: -
Gabor Juhos authored
Signed-off-by: -
John Crispin authored
Forgotten patch to fix ethernet for rt2880. Based on previously submitted patch from Claudio. Signed-off-by:Roman Yeryomin <roman@advem.lv> SVN-Revision: 40504
-
Felix Fietkau authored
Signed-off-by:Felix Fietkau <nbd@openwrt.org> SVN-Revision: 40503
-
Gabor Juhos authored
Signed-off-by:
André Valentin <avalentin@marcant.net> Patchwork: http://patchwork.openwrt.org/patch/5101/ [juhosg: remove the non-existing zyxelnand subtarget specific stuff] Signed-off-by:
-
Gabor Juhos authored
Signed-off-by:
-
Gabor Juhos authored
Signed-off-by:
-
Gabor Juhos authored
With this patch OpenWRT supports the following on the ZyXEL NBG 6716: -WiFi 2G (ath9k) -WiFi 5G (ath10k) -NAND flash -2 Ethernet interfaces -USB 2.0 -LEDs including switch -reasonale defaults at first boot Signed-off-by:
-
- Apr 12, 2014
-
-
John Crispin authored
Signed-off-by:John Crispin <blogic@openwrt.org> SVN-Revision: 40498
-
John Crispin authored
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework. Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process. Signed-off-by:Vittorio Gambaletta <openwrt@vittgam.net> SVN-Revision: 40497
-
John Crispin authored
This is required to make object "session" procedure "access" dump ACLs when no "object" or no "function" parameters are passed. Signed-off-by:Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 40496
-
John Crispin authored
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation. Signed-off-by:Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 40495
-
John Crispin authored
* gpio leds and buttons * ethernet Signed-off-by: -
John Crispin authored
* add pinctrl * fix ethernet port * make wifi available by default Signed-off-by: -
John Crispin authored
The last arg to FUNC() is count, not last pin. Signed-off-by: -
John Crispin authored
Signed-off-by: -
John Crispin authored
This change does multiple things, all related to enable sparse usage as a static analysis tool selectable from the OpenWrt configuration: *add a KERNEL_SPARSE option in the config to add sparse to the kernel build (through the C=1 option usage) *add sparse as a new host tools. It will get selected automatically when the above option will be enabled Signed-off-by:Mathieu Olivari <mathieu@qca.qualcomm.com> SVN-Revision: 40490
-
John Crispin authored
Signed-off-by: -
John Crispin authored
Signed-off-by:Daniel Schwierzeck <daniel.schwierzeck@gmail.com> SVN-Revision: 40488
-
John Crispin authored
Signed-off-by: -
John Crispin authored
Signed-off-by: -
John Crispin authored
Signed-off-by: -
John Crispin authored
Signed-off-by: -
John Crispin authored
Signed-off-by: -
John Crispin authored
Patches created from tree: git@github.com:danielschwierzeck/u-boot-lantiq.git v2013.10..u-boot-lantiq-v2013.10-openwrt4 Signed-off-by: -
Gabor Juhos authored
Based on the the WNDR3700v4 support patch from Ralph Perlich: http://patchwork.openwrt.org/patch/4763/ Signed-off-by:
-
Gabor Juhos authored
Signed-off-by: -
Gabor Juhos authored
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300 is the same device. Indicate this in the kernel files. Signed-off-by: -
Gabor Juhos authored
The 5V power of the USB is controlled by a GPIO pin of the external WiFi chip. Setup the GPIO bitmasks in the platform data of the WiFi chip to ensure that the 5V power gets enabled by the ath9k driver. Based on the the WNDR3700v4 support patch from Ralph Perlich: http://patchwork.openwrt.org/patch/4763/ Signed-off-by:
-
Gabor Juhos authored
Based on the the WNDR3700v4 support patch from Ralph Perlich: http://patchwork.openwrt.org/patch/4763/ Signed-off-by:
-
Gabor Juhos authored
Signed-off-by: -
Gabor Juhos authored
Based on the the WNDR3700v4 support patch from Ralph Perlich: http://patchwork.openwrt.org/patch/4763/ Signed-off-by:
-
Gabor Juhos authored
The bootloader does not initializes the output function correctly for all LEDs. DO that from the board setup code. Signed-off-by: -
Gabor Juhos authored
The hardware manual says amber so change the color part of the LED names to reflect that. Also update the constant names. Based on the the WNDR3700v4 support patch from Ralph Perlich: http://patchwork.openwrt.org/patch/4763/ Signed-off-by:
-
Gabor Juhos authored
Signed-off-by:
Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/5109/ Signed-off-by:
-
Gabor Juhos authored
Adds support for the received signal strength indicator LEDs of the Bullet M, Nanostation M and Rocket M devices. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
